Tutorial Tuesday - Single Fold Quilt Binding

Binding Tutorial Single fold The crafty Nomad.png

I've been meaning to add a binding tutorial to the website for a while now.  So today's post is for single fold binding.  I will be adding a post on double fold binding soon too! 

Single Fold binding is how I was first taught to bind a quilt by my friend Lorraine, on more recent quilts I have used double fold binding.  But for all my classes on patchwork and quilting I taught single fold binding.

First up measure all the edges of your project, add these numbers up and 10 inches.  This is the length of binding you need to make.  Cut strips that are 1 and 7/8 inches wide - I know it's a very specific figure!  Piece these strips together.  I like to do this on the bias to spread the bulk of the seam.  Lay the strips crossed over right sides together as shown. So lay one strip right side up and lay the next one right side down crossways at the corner.  Using an acrylic ruler with a 45º angle marked on it draw a line as shown.  Stitch directly on the line.  Trim to quarter inch seam allowance.  Press seams open.  Repeat until you have the necessary number of strips sewn together.  Using a bias tape maker (these gadgets are fab for preventing burnt fingers!) feed the strip of fabric in wrong side facing up.  Use a pin to help it through or if necessary cut the end into a point.  Gently pull it through and iron the folds into place, the raw edges should meet in the middle.  Now fold together so raw edges are inside and folded edges meet perfectly and iron in place.  Wrap around a piece of cardboard to help keep the folds in place and keep it clean and off the floor.

Open out all those folds.  Starting in the middle of an edge away from a corner, leave about 6 inches free, pin the binding right sides against the right side of the front, as shown, all around the table runner.  When you reach a corner, fold the binding as shown below and continue all the way around.

When you reach the place you started lay the left hand tail on top of the right hand tail.  Using your acrylic ruler mark a 45 degree line.  Fold back the top layer carefully and mark a corresponding line on the binding underneath.  Trim to a quarter inch past this line on both ends.  Pin together lay flat to check you've pinned it correctly.  Sew on the line.  Trim away the dog ears.  Lay flat, finger press the seam open and pin in place.  Using a walking foot stitch in place, along the first fold or just ever so slightly to the right of it.  When you reach a corner, stop when you can feel the extra layers of fabric beneath, you don't want to sew over those.  It should be about half an inch from the end.  Secure your stitches.  Fold the flap of fabric out of the way.  Insert the needle a half inch from the edge and continue.

Re-form the folds and flip the binding to the back.  Mitre the corners neatly.  Pin in place and hand stitch all the way around with an invisible ladder stitch.

I'll post a tutorial soon for the double fold binding.  The main benefit to single fold is that it uses less fabric.

Interested in the tools I used?  Here are some affiliate links.

Tutorial Tuesday - Wraparound Quilt Binding

Hi guys.  So as some of you will have seen over on my Facebook page last week, I made a quilt for my lovely aunt who turned 80 this year.  I'll share that with you on here soon.  Whilst making that quilt I was kind of up against it time-wise! So instead of doing traditional hand sewn binding like I normally do, I did wraparound binding instead.  So today I'm going to show you how to do that.  I know that those of you who groaned during classes when I mentioned hand sewing are going to LOVE this!

  • OK so first you'll want to make sure that your quilting stops about half an inch from the edge of your quilt top.  Any ends will need to be buried, as the back won't be covered by binding.

  • With scissors carefully trim away the excess batting / wadding.  Leaving the backing in place.

  • Trim the backing so there is an inch excess on all four edges.

  • At each corner fold the corner in at corner and finger press.  Open up and fold the corner into the fold line and finger press.  Open out and cut along the second fold line you made.  This reduces some of the bulk at the corners when a lovely mitred corner.
  • Using an iron, fold and press the backing fabric in half and inch along one edge so that the raw edge of the backing fabric meets the quilt top.  Press in place.  Now fold it over another half inch so that it has wrapped around and is now sitting on the front covered the raw edge of the quilt top.  Press in place along one edge.  Pin.
  • At the corner fold in at a 45 degree angle as shown.  Then repeat the process above: folding the backing in half and inch, pressing in place, then folding in again another half inch and pressing.  
  • Repeat this process until all four edges and corners are done and pinned in place.
  • Now edge stitch in place with your sewing machine.  Ideally using a walking foot.  Pivot at each corner.  Your stitching should be no more than an eighth of an inch from the quilt top.  I would not recommend reverse stitching, instead bury your ends inside the quilt.

Hope that all makes sense?!